Description
- Description
- Features and Benefits
- Specs
- Labels and SDS Forms
Fuse Foam Ready-to-Use Termiticide Insecticide contains Fipronil and Imidacloprid, the same proven, non-repellent active ingredients as the Fuse Termiticide Insecticide, but in a ready-to-use foam that is easy-to-apply. For Direct Injection into termite and ant nests and galleries, structural voids, and other sites. Fuse Foam is the latest addition to the Control Solutions Inc. (CSI) products for managing termites and other wood-destroying pests. Fuse Foam gives PMPs the opportunity to begin treating a structure immediately, right on the sales call; then schedule the full treatment for later. When it comes to stopping termites and ants, and preventing their spread inside a structure and with a 30:1 expansion ratio, Fuse Foam gives PMPs the ability to reach those tough-to-treat places with confidence. This was previously packaged in 20 oz can - now 15 oz. can.
The Fuse Foam Ready-to-Use Termiticide Insecticide can has recently been updated to include a new actuator. Ths new feature will allow you to make one-handed applications, it’s easier to use in tight and confined spaces, easier to treat wall voids, and safer to use when on a ladder.
WOOD DESTROYING TREATMENTS – OUTDOORS
Outdoor treatment locations may include infested trees, shrubs and tree stumps, and exterior wooden elements associated with bridges, decks, fencing, landscape timbers, wooden retaining walls, siding, channels in damaged wood, spaces between wooden elements of a structure, junctions between wood and foundations and voids associated with buildings. Applications to exposed subterranean termite tunnels, shelter tubes, may be made to both residential and commercial outdoor areas. Crack open a section of the shelter tube and apply directly over the exposed area. Apply enough FUSE FOAM to cover the exposed area and a distance of approximately 2 inches in each direction over the shelter tube itself.
Outdoor applications of this product must be limited to small spot treatments (not to exceed 2 sq. ft.) only.
TERMITES AND CARPENTER ANTS HARBORING IN STUMPS, UTILITY POLES, SLABS AND FENCES:
Drill 1 or more holes into areas of suspected termite or ant activity. It may be necessary to drill several holes around the circumference of the stump or utility pole, to properly treat the nest or gallery system. When treating below slabs, drill 1 or more holes through the slab where termites or carpenter ants are active, or suspected, and inject this product. For fences, treat exposed surfaces with this product where termites or ants are active (IMPORTANT: the foam must dissipate or excess foam must be removed before the applicator leaves the area) and/or drill wooden members where termites or ants are active, or suspected, and apply.
FORAGING CARPENTER ANTS:
Fuse Foam is intended for outdoor treatments for ant harborages or trails associated with decks, fences or other non-structural elements. Inject this product into galleries, cavities, harborages or structural voids. Apply the foam up to a 6” length of the ant trail. IMPORTANT: the foam must dissipate or excess foam must be removed before the applicator leaves the area.
CARPENTER BEES:
For use as a localized treatment. Apply foam directly into gallery entrance holes. Following treatment with the foam, the entrance holes may be plugged with a suitable material. IMPORTANT: the foam must dissipate or excess foam must be removed before the applicator leaves the area.
EXTERIOR PERIMETER/LOCALIZED INTERIOR
TERMITES [SUBTERRANEAN (Coptotermes, Reticulitermes, Heterotermes and Zootermopsis), and Arboreal]: FUSE FOAM can be used as a preventative for interior structural void treatment for subterranean termites. Interior applications to vulnerable areas are only intended for localized areas of existing or potential termite activity and must not be applied to indoor surfaces for the purposes of general pest control. FUSE FOAM is not for use as a substitute for soil applied termiticide treatment(s) beneath slabs or foundations.
Targeted interior application(s) of FUSE FOAM may be made to vulnerable areas such as voids associated with plumbing/utility lines penetrating floors, bath and/or shower voids, expansion joints and/or settlement cracks, wall voids and other voids of probable or potential termite entry.
NON-WOOD DESTROYING PEST TREATMENTS CRAWLING PESTS - Ants (Excluding Fire, Harvester, Leaf Cutter and Pharaoh): To kill ants in houses and other structures. This is not a substitute for mechanical alteration, soil or foundation treatment. Treat voids with this product, where these pests enter, hide or harbor. Apply by crack and crevice application. Apply to sufficiently cover the area, but do not allow excessive dripping or run-off to occur. Immediately wipe up any excess product on exposed surfaces.
Fuse Foam Ready-to-Use Termiticide Insecticide contains Fipronil and Imidacloprid, the same proven, non-repellent active ingredients as the Fuse Termiticide Insecticide, but in a ready-to-use foam that is easy-to-apply. For Direct Injection into termite and ant nests and galleries, structural voids, and other sites. Fuse Foam is the latest addition to the Control Solutions Inc. (CSI) products for managing termites and other wood-destroying pests. Fuse Foam gives PMPs the opportunity to begin treating a structure immediately, right on the sales call; then schedule the full treatment for later. When it comes to stopping termites and ants, and preventing their spread inside a structure and with a 30:1 expansion ratio, Fuse Foam gives PMPs the ability to reach those tough-to-treat places with confidence. This was previously packaged in 20 oz can - now 15 oz. can.
The Fuse Foam Ready-to-Use Termiticide Insecticide can has recently been updated to include a new actuator. Ths new feature will allow you to make one-handed applications, it’s easier to use in tight and confined spaces, easier to treat wall voids, and safer to use when on a ladder.
ACTIVE INGREDIENT | Fipronil 0.005% Imidacloprid 0.02% |
TARGET PESTS | Termites (Subterranean, Drywood, Dampwood & Arboreal); Wood Destroying , Carpenter Bees, Asian Lady Beetles, Box-elder Bugs, Cluster Flies, Elm Leaf Beetles, Bean Plataspids (including Kudzu Bug), Brown Marmorated Stink Bug |
FOR USE IN | Wood in Decks, Fencing or Siding, Channels in Damaged Wood, Spaces between Wood, Junctions Between Wood & Foundations * For Use in Residential Structures for Termite or Wood-Infesting Insect Attack |
APPLICATION | * See label for complete application instructions |
MANUFACTURER | Control Solutions |
EPA REGISTRATION | 87093-5-53883 |
NOT FOR SALE TO | AK, CA, PR CT, NY (Restricted To Licensed Applicators Only) |
Payment & Security
Your payment information is processed securely. We do not store credit card details nor have access to your credit card information.